CORSA MOTORWORKS / PASSION MEETS PERFORMANCE ENGINEERING YOUR NEXT CHAPTER
BMW ENGINES / S58 / STAGE 2
S58 engine block showing the cylinder boresS58 / ENGINE PROGRAM

CORSA MOTORSPORTS PACKAGE

S58
Stage 2 engine build

A coordinated upgrade to the rotating assembly and cylinder head.

$15,000.00 BASE BUILD / USD
COMPLETE YOUR BUILD

What goes into your build.

  • CP-Carrillo pistons with forged connecting rods
  • Oversized ARP studs with block machining
  • King main bearings and ACL rod bearings
  • GSC valve springs, retainers and valve-stem seals
  • BMW OE main seals
  • Fire-ring head gasket with matching block preparation
  • Kelford / GSC camshaft specification
  • GSC intake and exhaust valves
CONFIGURED BUILD TOTAL$15,000.00

Engine core, freight and taxes are additional. Installation is optional at the price shown. Core sourcing is quoted separately.

DISCUSS THIS BUILD ↗

CORSA MOTORWORKS / STAGE 2

HOW CORSA MOTORWORKS BUILDS YOUR ENGINE

More than the upgrades.

On top of the upgrades you select, every Corsa Motorworks engine receives a detailed preparation and assembly process—from teardown and inspection to machining, cylinder-head service and clean-room assembly.

  1. 01

    Complete teardown & detailed inspection

    A strong build starts by understanding the engine in front of us. Corsa Motorworks disassembles the engine so the block, crankshaft, pistons, rods and cylinder head can be evaluated individually. We look for scoring, heat damage, cracks and abnormal wear, then measure critical dimensions and clearances. Those findings establish which parts can be reused, which need replacement and what machining the build requires.

  2. 02

    Deep cleaning & passage preparation

    Precision work needs clean surfaces. Carbon deposits, oil residue and old gasket material are removed from the components being prepared. Oil galleries, coolant passages and threaded holes are cleaned and checked so contamination does not follow the engine into assembly. After machining, parts receive another thorough cleaning to remove abrasive residue and metal particles.

  3. 03

    Cylinder honing & piston fit

    The cylinder finish is part of the build, not an afterthought. Bore diameter, taper and out-of-round are measured before the honing plan is set. Honing prepares the cylinder geometry and surface finish for the chosen pistons and rings. Piston-to-wall clearance and ring end gaps are checked against the selected component specification, giving the rotating assembly a measured foundation.

  4. 04

    Block decking & cylinder-head resurfacing

    The head gasket depends on the surfaces beneath it. The block deck and cylinder-head face are checked for flatness, surface condition and previous material removal. Where required, decking and resurfacing restore suitable mating surfaces with a finish matched to the gasket system. Material removal is planned with engine geometry, compression and component clearances in mind.

  5. 05

    Cylinder-head cleaning & inspection

    The cylinder head is stripped so the combustion chambers, ports, valves and valvetrain can receive individual attention. Cleaning exposes deposits and wear that can hide beneath the surface. The head is checked for damage, the sealing face assessed, and the valves, seats and guides inspected before the repair and machining scope is finalized.

  6. 06

    Valve job, guides, seals & lapping

    Valve sealing receives its own careful work. Valve stems and guides are measured, worn guides are replaced as needed, and guide clearances are set for the selected valves. The valve job restores the required seat geometry and contact pattern. Where suitable for the valve and seat materials, lapping helps check contact before the components are thoroughly cleaned again. New valve-stem seals are installed, and valve sealing, spring setup, retainers and installed heights are checked before the head is assembled.

  7. 07

    Machining matched to your stage

    The machine work follows the complete specification. Depending on inspection findings and stage, that can include cylinder preparation, deck work, fastener machining and cylinder-head work. Stage 2 and Stage 3 incorporate the preparation required for oversized studs; Stage 3 also includes 5-axis CNC head porting and a full valve job. Dimensions are checked as the work progresses so the parts are prepared to function together.

  8. 08

    Clean-room assembly & final checks

    Once the parts are ready, the focus shifts from preparation to precision assembly. In a clean, controlled assembly environment, components are organized and protected from contamination. Bearing clearances, piston-and-ring fit, assembly lubrication and fastener torque procedures are checked as the long block takes shape. Cam timing and sealing details receive a final review, and the agreed specification is recorded on your Corsa Motorworks build sheet.

Inspection determines the final repair and machining scope. Required guide replacement, resurfacing or other additional work is confirmed with your build sheet and quote.

PLATFORMS58
BUILD TARGET1,200 WHP
STANDARD DISPLACEMENT3.0L

Your Corsa build starts here.

Share your vehicle, current setup and goals. Corsa Motorworks will review the core, finalize components and machining, and confirm your quote and production schedule before work begins. Break-in instructions accompany the agreed build.